Advanced Firewall Settings

The Advanced Firewall Settings allow you to add, edit, and remove rules pertaining to incoming and outgoing Internet traffic. Advanced Firewall Settings take precedence over rules for Internet Programs.

Note: If you configured Pioneer Complete Suite for multiple users or if you have required a password for changing Pioneer CompleteSuite settings, you have to log in as a Privileged User or provide your E-mail address and Password in order to change Advanced Firewall Settings.

Adding an Advanced Rule

To create an Advanced Rule:

On the Pioneer Complete Console, click the Firewall button .
On the Firewall menu, click Firewall Settings.

In the left pane of the Pioneer Complete Suite Settings window, click Advanced.
Click Add.
In the Advanced Firewall Rule window, in the Description text box, type a description for the rule.
In the Rule type option, select one of the following:

Allow network traffic – Select this option to create a rule allowing Internet traffic to and from your computer.
Block traffic – Select this option to create a rule blocking Internet traffic to and from your computer.

In the Remote system option, select one of the following:

All – The rule applies to all remote systems.
IP Address(es) – Type the single IP address or comma-separated address list for which you want the rule to apply.
IP Subnet – Type the IP Subnet Address and Mask for which you want the rule to apply.

In the Protocol option, select one of the following:

Any – The rule applies to all protocols.
TCP – The rule applies to Transmission Control Protocol traffic.
UDP – The rule applies to User Datagram Protocol traffic.
ICMP – The rule applies to Internet Control Message Protocol traffic.

In the Local Port(s) text box, type a local port or comma-separated list of ports for which the rule applies (optional).
In the Remote Port(s) text box, type a remote port or comma-separated list of ports for which the rule applies (optional).

Note: Not all protocols use ports and these options are only available for UDP and TCP.

In the Type(s) drop-down list, select a type of communication (optional).

If you selected IP in Step 8, you can now further specify the types of IP that you want to create a rule for:

2: IGMP – Internet Group Management
4: IP in IP – Encapsulation
8: EGP – Exterior Gateway Protocol
9: IGRP, IGP – Interior Gateway Protocol
46: RSVP – Reservation Protocol
47: GRE – General Routing Encapsulation
50: ESP – Encapsulating Security Payload
51: AH – Authentication Header
53: SWIPE – IP with Encryption
103: PIM – Protocol Independent Multicast
115: L2TP – Layer Two Tunneling Protocol

If you selected ICMP in Step 8, you can now further specify the types of ICMP that you want to create a rule for:

0 – Echo Reply
3 – Destination Unreachable
4 – Source Quench
5 – Redirect
6 – Alternate Host Address
8 – Echo Request
9 – Router Advertisement
10 – Router Solicitation
11 – Time Exceed
12 – Parameter Problem
13 – Timestamp Request
14 – Timestamp Reply
15 – Information Request
16 – Information Reply
17 – Address Mask Request
18 – Address Mask Reply
30 – Traceroute
31 – Datagram Conversion Error
32 – Mobile Host Redirect
33 – IPv6 Where-are-you
34 – IPv6 I-Am-Here
35 – Mobile Registration Request
36 – Mobile Registration Reply
37 – Domain Name Request
38 – Domain Name Reply
39 – SKIP
40 – Photuris [RFC2521]

In the Traffic Direction option, select one of the following:

Incoming – The rule only applies to incoming traffic.
Outgoing – The rule only applies to outgoing traffic.
Both – The rule applies to both incoming and outgoing traffic.

Click Apply to save the rule, and then click OK to close the Advanced Firewall Rule window.
Click Apply. If you require your E-mail address and Password to change Firewall Settings, the Password Required dialog box displays. Type your E-mail address and Password, and click OK.
Click OK to close the Pioneer Complete Suite Settings window.

Editing an Advanced Rule

To edit an Advanced Rule:

On the Pioneer CompleteConsole, click the Firewall button .
On the Firewall menu, click Firewall Settings.

In the left pane of the Pioneer Complete Suite Settings window, click Advanced.
Select the rule you want to change and click Edit.
Continue at Step 5 of Adding an Advanced Rule above.

Removing an Advanced Rule

To remove an Advanced Rule:

On the Pioneer Complete Console, click the Firewall button .
On the Firewall menu, click Firewall Settings.

In the left pane of the Pioneer Complete Suite Settings window, click Advanced.

The Pioneer Complete Suite Settings window displays any existing rules in the right pane.

Select the rule to remove.
Click Remove.
Click Apply to save the changes, and then click OK to close the Advanced Firewall Rule window.
Click Apply. If you require your E-mail address and Password to change Firewall Settings, the Password Required dialog box displays. Type your E-mail address and Password, and click OK.
Click OK to close the Pioneer Complete Suite Settings window.